Category: Stick (page 2 of 11)

Stick Welding Aluminum and a little known trick for Tig welding





Stick Welding Aluminum

Video Transcript:

Stick Welding Aluminum and a little known trick for Tig welding

Hey, Jody here. Today, we’re doing a little stick welding aluminum. Not my favorite thing, but I’m going to try a little quarter inch lap joint, and we’ll do a cut and etch test on it, compare results from stick welding cold with no pre-heat to weld it while it’s hot from the previous weld and see the difference there. What I really want to talk about today is something that I bet you didn’t know. I saw a video years ago … can’t find it now, but I saw a video years ago of a guy repairing an aluminum pump housing, a cast aluminum pump housing. He was using a scratch start TIG rig on DCEN. But for filler rod, he was using an aluminum stick electrode with the flux on, and it wasn’t looking bad at all.
That’s interesting to me, and we’re not talking about something that you would want to do all the time. But there are times when you’ve got to just do something in a pinch, a temporary repair until you can fix it the right way, things like that. We’re going to do a little bit of that today, and also, we’ll do a little cut and etch on that. Let’s dive in.
All right. For the stick welding, I’m using these Hobart 1/8th diameter rods. That’s 3.2 millimeter. 120 amps DCEP, electrode positive. That’s also called reverse polarity. And I tried a few at a slightly lower amperage, and they definitely needed the full 120. I’m welding on a quarter inch thick, roughly 6 millimeter thick, material, and it’s a lap joint. And you can see how hard it is to distinguish the puddle from the flux. It’s just kind of a mess. Lots of spatter. Lots of slag. It’s kind of ugly, but it stuck these pieces together.
Now, we’re going to run a beat with the TIG welder using these Blue Demon rods. These are smaller diameter. I ordered two different brands just to get two different diameters. I ordered on Amazon, by the way. I’ll put some links in the description box for these things. I’m sticking the tungsten barely even extending out, because I want this to be kind of a brazing operation. I don’t want to contaminate my electrode. I figure all that flux popping around is going to jump onto the electrode.
I think, actually, I could’ve run it up in the cup a little bit more, and it might’ve worked even better. But I’m adding quite a bit of rod here, and that’s because a lot of the flux is just going to slag. It’s not going in the weld, and you’ll see that in the arc shot in just a second. Flux going everywhere. See it running all down there? But you can kind of distinguish a puddle. And so once you get that sort of distinguished and get the heat right, it kind of goes better than you might think.
This is 8th of an inch thick material, by the way, 3.2 millimeter thickness. Running around 140 amps here, and I’m using the foot pedal, just because I really didn’t have any idea how much amperage it would take. And it’s pretty ugly compared to a TIG weld, but then again, it’s looking better than I thought it would. So this would do in a pinch as kind of a last resort, emergency type repair, if you didn’t have an ACDC TIG welder.
Well, let’s get some results here with a quick cut, polish, and itch on this stick weld. It looked horrible going in. Didn’t look that great on the final product, either, and look at all that porosity. But what we learned here is with the pre-heat … like, I welded this one while it was still hot, and it came out much better. Let’s take a look at the one we TIG welded with the flux on the rod. I mean, the weld nugget itself is just not really too bad. Got decent penetration, very little porosity. read more

Overhead Welding with 7018 and Dual Shield Flux Core



Dual Shield Flux Core

Below are some products that I don’t carry, but I use them in my videos and can vouch for their quality.

WELDING MACHINES

Lincoln Viking 3350 w/4C

http://amzn.to/2rRFlUn

Lincoln Square Wave TIG 200 read more

7018 Vertical Uphill Lincoln vs Hobart




7018

Video Transcript

7018 Vertical Uphill Lincoln vs Hobart

All right, you know, sometimes when I set out to film a video, I imagine this happens to everybody. You start off with an idea and then it kind of takes its own form and turns into something a little different. Today I started off wanting to compare Lincoln Excalibur 7018 to some Hobart 7018 I got from Tractor Supply. I wanted to do the comparison on vertical uphill lap joints, 1/4 inch thick metal. That’s roughly six millimeter thick metal. I’m using 332, that’s 2.4 millimeter 7018, and just stuff happened and it just turned into something a little different, but I think we can all learn something from it anyway. This is not a sponsored video. You’ll see that as I go along. All right? Let’s do it. read more

Rocket Stove Welding Project




Rocket Stove

New Website: WeldmongerTools.com

WM_Tools™_Dirty_Profile

Welders!

I’d like to thank you personally for being a subscriber to my videos and to this “vlog”. You guys are the best.

I thought I’d just make quick announcement that’s going to be very exciting for a lot of you…

I get questions all the time like, “What sort of welding machine should I buy?” or “Where can I get a bargain on gear?” read more

Older posts Newer posts

© 2017 Weldmonger™

Back to Top ↑